The site is read-only. Please transition to use Robotics Stack Exchange
| ROS Resources: Documentation | Support | Discussion Forum | Index | Service Status | ros @ Robotics Stack Exchange |
| 2021-12-27 18:15:16 -0500 | received badge | ● Famous Question (source) |
| 2021-12-27 18:15:16 -0500 | received badge | ● Notable Question (source) |
| 2021-05-19 10:34:48 -0500 | marked best answer | ¿GPS Glonass Ublox7 with nmea_serial_driver? Hello I am trying to connect a GPS Usb Glonass Ublox7 with nmea_serial_driver and I can't. I have checked where it is connected using ls / dev / tty * and I have it connected in ttyACM1. If I run the command: $ sudo cat /dev/ttyACM1 or $ sudo cat /dev/gps1 I get NMEA sentence. However when executing the command: $ rosrun nmea_serial_driver _port:/dev/ttyACM1 _baud:=115200 I get the following error that can't open port The Glonass GPS supports any standard baud rate. If I run the following command: $ groups <myusername> I get the following: <myusername>: lauratfg adm dialout fax cdrom floppy tape sudo audio dip video plugdev input nopasswdlogin lpadmin scanner gpio i2c spi sambashare samba I don't know what else to do ... Help please. This gps doesn't work with nmea_serial_driver? Thank you. Greetings. |
| 2021-01-26 21:34:00 -0500 | received badge | ● Popular Question (source) |
| 2021-01-26 10:47:11 -0500 | answered a question | nmea_navsat_driver and heading Hello, first of all if you see the corresponding driver.py code, the following appears within the code: "Creates the fol |
| 2021-01-26 10:47:11 -0500 | received badge | ● Rapid Responder (source) |
| 2021-01-26 07:20:10 -0500 | received badge | ● Necromancer (source) |
| 2021-01-26 07:20:10 -0500 | received badge | ● Self-Learner (source) |
| 2021-01-26 07:20:10 -0500 | received badge | ● Teacher (source) |
| 2021-01-26 07:19:02 -0500 | received badge | ● Famous Question (source) |
| 2021-01-25 12:07:09 -0500 | answered a question | ¿GPS Glonass Ublox7 with nmea_serial_driver? The problem was that I had the gpsd daemon installed. The solution has been to find which process was using the port for |
| 2021-01-25 12:02:58 -0500 | received badge | ● Notable Question (source) |
| 2021-01-25 12:02:01 -0500 | asked a question | nmea_navsat_driver and heading nmea_navsat_driver and heading Good morning I am using the nmea_navsat_driver package via $ rosrun nmea_navsat_driver nm |
| 2020-10-29 08:51:14 -0500 | received badge | ● Popular Question (source) |
| 2020-10-29 01:22:47 -0500 | received badge | ● Popular Question (source) |
| 2020-10-28 10:39:38 -0500 | commented answer | ¿GPS Glonass Ublox7 with nmea_serial_driver? I have already tried. I get the same. |
| 2020-10-28 10:39:31 -0500 | edited answer | ¿GPS Glonass Ublox7 with nmea_serial_driver? I have already tried. I get the same. |
| 2020-10-28 10:38:50 -0500 | edited answer | ¿GPS Glonass Ublox7 with nmea_serial_driver? I have already tried. I get the same. |
| 2020-10-28 10:38:50 -0500 | received badge | ● Editor |
| 2020-10-28 10:38:04 -0500 | answered a question | ¿GPS Glonass Ublox7 with nmea_serial_driver? I have already tried. I get the same. |
| 2020-10-28 10:38:04 -0500 | received badge | ● Rapid Responder |
| 2020-10-27 17:22:06 -0500 | asked a question | ¿GPS Glonass Ublox7 with nmea_serial_driver? ¿GPS Glonass Ublox7 with nmea_serial_driver? Hello I am trying to connect a GPS Usb Glonass Ublox7 with nmea_serial_driv |
| 2020-10-27 17:11:39 -0500 | edited question | ¿GPS Glonass Ublox7 con nmea_serial_driver? ¿GPS Glonass Ublox7 con nmea_serial_driver? Hello I am trying to connect a GPS Usb Glonass Ublox7 with nmea_serial_drive |
| 2020-10-26 14:41:08 -0500 | asked a question | ¿GPS Glonass Ublox7 con nmea_serial_driver? ¿GPS Glonass Ublox7 con nmea_serial_driver? Hola estoy intentando conectar un GPS Usb Glonass Ublox7 con nmea_serial_dri |
ROS Answers is licensed under Creative Commons Attribution 3.0 Content on this site is licensed under a Creative Commons Attribution Share Alike 3.0 license.